Gas Grill Regulator Problems: 7 Types Of Problems & Step by Step Solutions
Gas grills are a staple of many summertime BBQs. While gas grills are convenient and easy to use, they can still have problems. But even the best gas grill can have problems from time to time, and gas grill regulator problems are common.
One of the most common is a leaky regulator valve. Luckily, this problem is relatively easy to fix if you know what the issue is and how to address it.
Check out our blog post for more information! In this blog post, we’ll discuss what a gas grill regulator is and how it works, as well as some common problems with regulators and how to fix them!
There are 15 common problems that can occur and solutions for each one! Read on to learn more about the different types of gas grill regulator problems, how they happen, and their corresponding fix.
Table of Contents
What is a gas grill regulator?
A gas grill regulator is, simply put, a pressure regulator. It controls the amount of gas that flows from your propane tank into the burner tubes of the grill. This allows you to control how much flame comes out of each tube so you can adjust for weather conditions and cooking preferences.
As food cooks on the grill, it dims or brightens the flames by raising or lowering the burners’ valve knobs.
If more gas is needed, turning up either one or both valves will do the job nicely. If you turn them too high though, you’re going to get an inferno instead of an oven-like cooking environment!
Of course, it’s very possible that some basic gas grill regulator problems your current system are keeping you from getting a perfect flame – a gas leak, a clogged regulator, or a particularly high or low tank pressure can all do this.
How does a gas grill regulator work?
A regulator works by regulating the amount of propane that flows from your propane tank to your burners. The theory behind it is simple: the more pressure you put on the liquid propane, the more molecules are going to be squeezed onto the grill’s burner tubes.
That means that when there’s less pressure in your propane tank, fewer molecules will reach your burner tubes and thus less heat will be produced.
By squeezing every bit of juice out of your propane tank with a lot of pressure , you get a strong heat source capable of quickly boiling water or getting your steaks hot and ready for grilling.
However, if you want to save fuel (since it takes time to compress the gas), the regulator lets you turn down the pressure so that less heat is produced on your grill’s burners.
It’s like letting some air out of a balloon – if you let more air out, it takes longer to inflate, but when its full, there’s more volume inside. If you fill up an already big balloon with more air though, it’ll take even longer!
That extra volume will cost you energy too since more molecules are moving around trying to go through the regulator valve into burner tubes! There are two parts of every regulator and both of them can cause gas grill regulator problems – the main body and the valve knob .
The main body is the part of the regulator that attaches it to your propane tank. With a quick-release propane connector, it makes connecting and disconnecting your tank incredibly easy!
The valve knob allows you to adjust how much pressure goes into your burners so that you can control how high or low they are. Most regulator valves have gauges on them, allowing you to see just how much pressure is in your tank at any given time!
Is my gas grill regulator broken?
If you find yourself with no flame whatsoever, make sure that first and foremost, the fuel source itself isn’t empty. It’s possible for some grills to lose connection between their hose and their regulator valve – reconnecting might fix this issue.
But if this doesn’t work, your regulator might be the problem! In some cases, a regulator can break as a result of normal use. If you’ve been using yours for years without any real problems, it’s still possible to have one fail if you leave it under some intense heat or cold conditions.
It’s also possible that debris could get stuck in your valve knob , preventing it from working properly. And finally, dropping or mishandling your gas grill can cause damage to your regulator!
7 Types Of Gas Grill Regulator Problems And How To Fix Them
There are 7 types common issue with regulators – below, we’ll cover what they are and how to resolve them!
Problem 1: The flame is too high or low
If you’re having issues with your flame being too high or low, the regulator knob could be the problem.
This is because when there’s not enough pressure coming from your propane tank, it takes longer for the gas to come out of your valves and into your burner tubes – this means that you have to turn down your regulator in order to get a lower flame .
If this doesn’t work, it’s possible that debris got stuck in between parts of your regulator’s valve knob . If you can easily blow air through your reg , make sure nothing is blocking its path!
Also make sure that the hose leadingfrom the tank to the regulator valve isn’t kinked or bent. To resolve either gas grill regulator problems on this one, simply open up and clean any blocked-up parts, or bend or straighten your hose if it’s kinked.
If you’re still having issues, you might have faulty regulator valves! It’s possible that through normal use, they might get stuck.
The best way to resolve this problem is to ask a certified grill technician to take a look at them for you – here are some tips on finding one in your area .
Problem 2: My gas grill won’t stay lit
When something goes wrong with one of your burners’ pilot lights , it can be frustrating to say the least. If even after checking everything else (more details on what to check below), you can’t seem to get it back!
One reason could be due to low pressure This is because when there isn’t enough propane coming from your tanks, there’s not enough gas to keep the flame burning. Try turning up the pressure on your regulator !
If that doesn’t work, it might be that there’s a problem with your pilot itself. In these cases, it could have been compromised by debris getting stuck in between key parts of its system.
If you can easily blow air through your pilot , make sure nothing is blocking its path! Also make sure that the hose leading from the tank to the pilot is clean and free of kinks or bends.
Problem 3: My grill won’t turn off
If you’ve been trying to turn your gas grill off for a while, and it just won’t seem to budge, it might have something to do with low pressure .
It’s almost certain that the problem has nothing to do with your thermocouples , which are responsible for monitoring things inside of your grill.
In these cases, your burners may take a few minutes longer than normal to turn off – if they shut down at all! What we strongly suggest in this scenario is turning up the pressure on your regulator (more details on what to check below) and seeing if doing so gets them going again.
Problem 4: My grill won’t turn on at all
If you’re having problems getting your gas grill to light, there could be a few different issues. One of which is low pressure . As we laid out above, if there isn’t enough gas coming from your propane tanks, it will take longer for the flame to come on and stay lit.
In order to fix this gas grill regulator problems, try turning up the pressure on your regulator (more details below). Also make sure that the hose leading from the tank to the key parts of your system aren’t kinked or bent.
If they are clean and free of debris , simply open them up and see if that solves any issues!
If it doesn’t, there might be something wrong with your pilot itself. In these cases, the problem could have been caused by debris getting stuck in between key parts of its system.
If you can easily blow air through your pilot , make sure nothing is blocking its path! Also make sure that the hose leading from the tank to the pilot is clean and free of kinks or bends.
To resolve either problem, simply open up and clean any blocked-up parts, or bend or straighten out a bent or kinked hose.
Problem 5: My grill won’t turn off when I shut it down
When this happens, there’s usually nothing wrong with your thermocouples . However, if for some reason they’re never able to detect that your grill is off, they’ll keep the burners on.
While this does no serious damage to anything, it can waste gas! All you have to do is shut down everything inside of your grill . If the thermocouples are still faulty , be sure to replace them.
Problem 6: My regulator knob is stuck or doesn’t work at all
If your regulator isn’t working properly, it could be because something has built up between key parts of its system.
A common reason why this might happen is debris getting caught in between the key compression rings that are responsible for regulating pressure . The best way to fix any such problems is by opening up and cleaning those areas thoroughly .
Also make sure that nothing is blocking the path that gas takes into your regulator. Remember that the hose leading from the tank to the key parts of your system may be kinked or bent. If they’re clean and free of debris, simply open them up and see if that solves any issues!
If it doesn’t, you might need to replace your regulator or entire gas grill system.
Problem 7: The knob on my propane tank will only turn part of the way
If your tank’s regulator isn’t working properly, it could be because something has built up between key parts of its system. A common reason why this might happen is debris getting caught in between the compression rings that are responsible for the release of gas .
The best way to fix any such problems is by opening up and cleaning those areas thoroughly . Also make sure that nothing is blocking the path that gas takes into your regulator.
Remember that the hose leading from the tank to the key parts of your system may be kinked or bent. If they’re clean and free of debris, simply open them up and see if that solves any issues!
If it doesn’t, you may need to replace your entire gas grill system.
15 Problems with the regulator and how to fix them step by step
1. Low pressure reading on the regulator/low gas flow rate
This means that high pressure safety solenoid valve (inside your regulator) is not opening because it could be either stuck or broken (if your grill model has two safety valves, one inside the main regulator and second inside manual controller).
So in this case you will need to replace the entire regulator because there’s no way to clean or fix them without risking potential injury when all safety precautions are disabled.
2. High Pressure Gauge Drops Down Suddenly To Zero While Cooking
This usually means that one of your regulators safety solenoid valves is sticking closed which means escaping propane might continue to enter into the burner tubes when it should have stopped.
The moment when this happens, the regulator high pressure gauge will detect low pressure reading which it thinks is normal.
The only way to fix this is by replacing both your main and manual regulators with new ones or at least one replacement solenoid valves.
3. High Pressure Gauge Keeps Reading High While Cooking + Burning Smell & No Flame
This means that safety solenoid valve inside your main/main regulator (inside the control panel) is stuck closed while the other safety valve inside manual controller opened just fine when opened manually via plastic red button on top of it.
It’s probably broken due to overheating issues which usually happen when you run your grill on full blast without any ventilation for too long time.
In such case you need to replace all regulators and controllers or just manual controller (if your grill doesn’t have built-in electronic ignition system). This is one of common issues about gas grill regulator problems that I personally meet.
4. High Pressure Gauge Reads Low While Cooking & The Burner Keeps Igniting
If the regulator high pressure gauge reads too low then it means that lower orifice inside your main solenoid valve is clogged with debris and needs to be cleaned out.
To do this, first find lower/inner gasket at the bottom of your gas regulator, unscrew everything and take both whole pieces apart for cleaning process.
Then put them back together in reverse order (make sure that o-rings are correctly installed onto washers inside the housing).
5. Regulator Only Reads Low Gauge – Normal Pressure Reading on the Manifold
This means that you have faulty manifold with leaking or broken diaphragm which will require replacement.
It’s true that most modern grills are using combined regulator/manifolds but it’s also common for some high end gas grills to continue use separate regulators on top of manifold for more accurate pressure reading and increased durability.
6. Top Burner Stops Working + High Pressure Gauge Keeps Reading High While Cooking
If this is happening on your grill then there’s a good chance that there might be a problem inside safety solenoid valve inside your control panel (main regulator) because this is the one responsible for controlling propane flow rate to the top burners.
In such case you will need to replace it with a new one or at least clean/repair it properly for safe propane flow because all safety precautions are disabled when manual controller is not attached.
7. Regulator High Pressure Gauge Drops Down Suddenly To Zero While Cooking
This usually means that your regulator high pressure gauge itself is faulty which usually happens after few years of use, although if this happened suddenly then there’s definitely something wrong inside your main regulator/manifold because safety solenoid valves should continue working even when control panel is separated from manifold piping.
Problems like these can be prevented by replacing lower gasket every 1-2 years which you can do without special tools, just unscrew everything and put new gasket in place.
8. Regulator Gauge Reads Normal While Cooking But Still Keeps Cycling On And Off
This could be happening because your gas valve orifices are becoming clogged with debris after so long time of usage, propane flow might become too low for proper operation which leads to regulator cycling on/off while cooking because its electronic safety sensors are detecting low pressure problems which usually happen when there’s too much airflow over the burner tubes.
To fix this problem you need to replace your burners (if you can’t do it by yourself then take it to a local hardware store) or clean them thoroughly with wire brush if possible (after shutting off the gas) for removing all dirt, grease and rust.
It’s also possible that there’s a problem with one or more of safety solenoid valves located inside control panel because when they fail completely then grill starts cycling on/off while cooking without any problems detected by regulator high pressure gauge.
9. Main Burner Ignition Doesn’t Work + High Pressure Gauge Reads Normal While Cooking
If this is happening then you have faulty ignition spark generator which needs to be tested thoroughly (simply disconnect it from propane source and plug in the lighter).
If test light comes on for less than 3 seconds then your ignition switch might need replacement or repair if its contacts are burnt out.
10. Safety Valve Keeps Shutting Off And High Pressure Gauge Keeps On Fluctuating
This means that there’s a problem with controller assembly because it keeps cycling on/off continuously to protect the grill from overheating and causing gas leaks.
This will require replacement of controller circuit board which usually requires soldering stuff inside control panel pocket.
11. Regulator + Safety Valve Problems – “Grill Will Not Ignite”
This usually happens if your regulator or safety solenoid valves are defective and need replacement, but it could also be due to other reasons like worn ignition switch contacts (cause problems when grill tries to ignite) or low voltage power supply (plugged in wrong voltage).
12. Top Burner Only Works On High
If this is happening to you then there’s a good chance that safety solenoid valves are not working because it could be clogged with rust or dirt after years of usage, or it might be simply faulty.
The only solution for this problem is replacing your old faulty solenoid valves which can be done without soldering stuff inside control panel pocket which means that if you’re confident enough repair the valves yourself otherwise take it to local hardware store where they will test them properly.
13. Propane Smells Like Natural Gas When Grill Is Turned On And Flows Out Of Regulator While Cooking
This usually happens when main gas regulator is set too low and allows propane tank pressure to flow into the control panel piping when grill is turned on which causes gas smell, but it can also be caused by faulty regulator solenoid valves.
The only solution for this problem is switching to higher pressure regulator (30,000 BTU) or bleeding your propane tank before using grill because its too low for proper cooking performance.
14. Control Panel Will Not Ignite And High Pressure Gauge Keeps Fluctuating
This usually happens when there’s a clogged burner tube/orifices with debris after so many years of usage and once you clean them thoroughly then grill should start working without any problems at all.
15. Control Panel Is Making Sizzling Noises While Unit Is Still Cool But Will Not Ignite
This means that there’s a problem with one of safety solenoid valves inside control panel because when they fail completely then it starts making sizzling noises when grill is hot (after cooking) but it won’t ignite.
The only solution for this problem is replacing your old faulty solenoid valves which can be done without soldering stuff inside control panel pocket which means that if you’re confident enough repair the valves yourself otherwise take it to local hardware store where they will test them properly.
Warning signs that your regulator might be broken or needs to be replaced
If you notice any of the following warning signs, it might be time to get a new regulator for your gas grill :
- Your grill doesn’t turn on or come to temperature properly.
- The tank won’t stay attached to the regulator .
- You’re unable to adjust anything on your current regulator.
- It takes longer than usual for the flames on your grill’s burners to go down .
- Your grill switches between high and low pressure frequently.
Gas Grill Maintenance Tips
- Make sure your grill is clean and free of debris so that it doesn’t get in the way when you’re cooking .
- If your regulator starts giving you trouble, don’t be afraid to replace it with a new one .
- Test whether or not you need a gas hose upgrade by hooking up your grill’s tank to other sections of your system. If there are no problems, then there isn’t any need for an upgrade.
- Remember: The arrow printed onto most regulators’ adjustment knobs points towards a tightening direction!
Extra Tip 1: Save money on propane by using an automatic tank regulator
If you use propane tanks to power your grill, chances are good that at some point one of the problems above will affect you and your cooking. Luckily each problem has a solution and we’ve laid them all out for you here.
Another thing we strongly suggest doing is turning an automatic tank regulator into your propane gas grill’s permanent fixture.
An automatic tank regulator keeps track of how much gas is left in a tank , shutting off the flow of fuel once its capacity has been reached. This prevents wasted propane and money spent on refills.
However, it’s worth noting that because automatic tank regulators are reliant on tank pressure, any problems with your regulator will also affect them .
If you want to turn an automatic tank regulator into a permanent fixture in your grill, be sure to have a spare automatic tank regulator ready to go so you can swap it out if one fails!
Extra Tip 2: Save propane by using just the right amount of fuel
With many different factors affecting how much propane your grill uses , there’s no way around the fact that other than turning an automatic tank regulator into your grill’s permanent fixture or upgrading/replacing either part of your system entirely, there is only so much you can do save fuel.
What we mean by this is that while you can’t change the size of your tank, the specific propane brand you buy or where you buy it from , how much fuel your grill uses is ultimately controlled by features such as grill dimensions, airflow and several others.
To get a better idea of just how much fuel certain factors affect your propane consumption, we suggest using GrillGrate’s Fuel Calculator. It’ll tell you exactly how long each individual burner on your grill will run and for how many hours!
Due to their relatively small cost and ability to make things easier in many ways for grilling enthusiasts , we recommend always having 2-3 spare regulator valves around .
The reason for this is twofold:
First, because there are simply too many things that can go wrong with any of the key parts of your gas grill system, it is always good to have some extra valves on hand in case you need to replace one.
Secondly, this eliminates the possibility that you might not be able to get a replacement for your current regulator right away and end up having to use an inferior part instead .
Extra Tip 3: Switch out your gas hose with GrillGrate’s Quick Connect Kit
If you’ve ever had trouble hooking up a propane tank to any section of your system, you know how annoying this can be! Luckily, it’s an easy enough fix that you can easily do yourself. Please pay close notice to this tip if you want to prevent any gas grill regulator problems.
All the kit requires is the installation of a quick connect system that allows you to attach and detach your tank with ease .
Extra Tip 4: Keep an eye on your regulator’s adjustment knob
Most regulators have arrows printed onto their adjustment knobs, showing which direction to turn if they are too loose or too tight .
If it does become necessary for you to adjust the regulator knob on your propane grill, simply remember these two rules : Turning clockwise will tighten your regulator , while turning counterclockwise will loosen it.
To save both time and effort when adjusting any part of your gas grill , always start off by loosening then tightening in small increments first before making larger adjustments .
This will save you the hassle of having to go through all the adjusting steps in case what you did initially wasn’t enough.
How can I tell if there’s something wrong with my gas grill regulator ?
If you suspect something is wrong with your gas grill regulator problems, there are a few common symptoms to look for:
-The regulator won’t turn the gas flow on at all. In this case it’s usually just a bad connection or faulty solenoid valve somewhere in the system. A professional needs to troubleshoot and fix this problem.
-The regulator will turn off after a short time leaving you unable to control the flame size on your grill.
This problem may be due to a small leak somewhere in the system, but most often it’s caused by a bad orifice inside of the main burner tube which means that section would have to be replaced. Sometimes it can also occur if there’s some kind of blockageplerly.
-The regulator is not turning on the gas flow on enough (low pressure). In this case it’s usually just a bad connection or faulty solenoid valve somewhere in the system. A professional needs to troubleshoot and fix this proplerly.
-The regulator is turning on the gas flow too much (high pressure). In this case you need to replace your regulator with a new one, or if possible adjust your low pressure gauge setting to get the right pressure according to your grill manufacturer’s recommendations.
How do I know which of these 3 things is wrong?
As mentioned above there are only 3 problems that can occur: either there’s no gas flow at all, or gas flow rate is not high enough, or gas flow is too high.
All three of these problems have different causes and they need to be dealt with in different ways.
If you can’t get any gas flow at all when turning on the gas supply:
-Check solenoid valve wiring and connections for corrosion, breaks/disconnections and also make sure that the grill’s control knob is in the ON position.
If everything checks out OK then replace solenoid valve (it would be a good idea to replace both solenoid valves).
-If replacing the solenoid does not fix your no gas issue then check regulator pressure gauge & hose connection for blockage, kinks and leaks.
If there’s no blockage or leaks found in this area then replace the regulator (it would be a good idea to buy an universal gas grill regulator kit or universal replacement kit because it’s always better to have more spare parts than not enough).
If the gas flow rate is too high:
-Check your regulator pressure gauge & hose connection for blockage, kinks and leaks.
If there’s no blockage or leaks found in this area then adjust low pressure setting on your grill’s regulator until you reach the desired flow rate. If that does not solve your problem then replace your regulator with a new one .
-Please note that if adjusting the low pressure cannot fix your too high gas flow issue then it tells us that something has got blocked or clogged somewhere inside of the burner tube(s) or inside of the gas supply line. In this case you will need a professional to fix your gas grill regulator problems for you.
If the regulator is not turning on the flow rate of gas at all:
-Check solenoid valve wiring and connections for corrosion, breaks/disconnections and also make sure that the grill’s control knob is in the ON position.
If everything checks out OK then replace solenoid valve (it would be a good idea to replace both solenoid valves).
-If replacing the solenoid does not fix your no gas issue then check low pressure gauge & hose connection for blockage, kinks and leaks.
If there’s no blockage or leaks found in this area then replace your regulator (it would be a good idea to buy an universal gas grill regulator kit or universal replacement kit because it’s always better to have more spare parts than not enough).
-However if the low pressure is fine then check for blockage, kinks and leaks in into the burner tubes. If everything checks out OK there then replace the main pressure switch that controls your regulator.
-If none of these mentioned things fixed your regulator issue then most probably you have burned out your solenoid coils.
In this case you need to replace them both with new coils, or you can just buy a universal gas grill regulator replacement kit which includes all necessary solenoid valves & coils so no need to buy each separate.
How do I set the low pressure on my grill regulator?
-First of all make sure that the gas supply is completely turned off.
Then, using a flathead screwdriver or hex key wrench, turn your regulator’s adjustment screws to adjust the pressure until you reach the desired flow rate of gas (low pressure gauge should point towards zero).
-After adjusting the low pressure do not turn on the main gas supply switch yet!
Turn the control knob/switch on and if everything looks fine then turn on your gas supply. Only then it would be safe to use your grill without worrying about any potential hazards that might occur.
But I can’t set my low pressure because one/both of my adjustment screw(s) are stuck inside their threading! What should I do now?
-If one or both of your regulator adjustment screws are stuck inside their threading then you will need to use a wrench and carefully turn them towards the left (counter clock wise) until they can be removed.
However, please note that if too much force is applied when turning these screws this could result in broken/blunt screw head and cause more problems for you! If this does happen then you might need to replace the entire regulator.
Types of regulators
There are two types of regulators which are a) single stage and b) dual stage.
The main difference between them is the fact that the single stage has one pressure adjustment screw while the dual stage has two pressure adjustment screws.
In general, all kinds of gas grills have only one regulator so it’s always a single stage type.
If your grill is equipped with two or more regulators then the additional one(s) would be there for safety purposes in case something goes wrong with your primary solenoid valve/s which could cause an explosion if not detected fast enough.
However, many manufacturers do sell cheap propane grills which have a dual regulator installed inside them just to make their customers believe that they’re getting high quality product.
They do this so at the point of sale their grills will sound better than if they had a single stage regulator and thus sell more grills. But, aside from looking fancy and sounding good, these dual regulators do not work any different than a single stage.
Where to find parts for your grill?
-Some gas grills have universal replacement kits that include all required or fre essentials such as new regulator/s with solenoid valves & coils (if applicable), low pressure gauge and rubber hoses etc., while some companies also include additional high pressure hose(s).
If you’re lucky then you might be able buy one of these kits which should fix your main problem, but it’s always better to call your manufacturer just to double check.
-If you can’t find any kit, or if the kit doesn’t fit your grill then it’s good idea to call them and ask where you might be able to buy replacement parts since they should have this info on their website/catalogs.
If not then there are other ways to get new parts but that will require more effort because you’ll need to search for individual parts which will need some research time invested into it.
FAQs about gas grill regulator problems
Why do gas grill regulators fail?
Gas grill regulators fail because of misadjusted low pressure and bad solenoid valves or coils.
Can you bypass a propane regulator?
Yes, but only temporarily. If the problem is with the regulator then bypassing it won’t fix anything because that’s where your flow of gas gets regulated to match your grill’s needs.
It would be like replacing a broken fuel pump on your car instead of fixing what is causing it to not work properly (e.g., clogged filter).
How do you test a regulator?
You can check if your regulator is working correctly by turning on all control knobs/switches and carefully listening for hhissssssss sound of propane flowing through its tubings.
But keep in mind that sometimes this hiss can also come from open parts or leaky connections which are not directly related to the regulator itself.
Keep reading if you are interested in common questions about gas grill regulator problems.
Can you test propane tank with a regulator?
Yes, if your grill does not have a built in pressure gauge then you might be able to install the regulator and connect it to the propane tank.
But keep in mind that this can only tell you if your grill’s regulator is working correctly or not since there are other factors involved such as defective replacement parts.
How much pressure should your grill use?
Average grills will require between 11″ and 15″ of water column (WC) which equals 116 psi and 173 psi at room temperature respectively.
This info is based on average 1 lb. disposable propane tanks which produce about 100,000 BTUs for each 20 lb. cylinder (~2″ vs ~8″ WC).
How to fix regulator problems?
If your grill is leaking gas or not working properly then it’s best that you get a replacement regulator/s, low pressure gauge and new coils (if necessary) in order to fix the gas grill regulator problems.
You can try jumpering the solenoid valve(s) with a high wattage resistor in order to heat up its’ coils faster but this would only help in some cases since they tend to burn out fast due to dirty build up inside them.
High quality grills have electronic ignition which replaces coils, while less expensive ones use jumpering method which is basically an indirect form of electronic ignition because when heated from jumpering they tend to work sometimes… for a while at least.
What PSI should a gas grill regulator be?
It’s a good idea to keep your grill within the manufacturer’s recommended pressure range.
But before buying a regulator make sure that it can reach between 1″ and 5″ WC which equals 116 psi and 762 psi at room temperature respectively.
Final words about gas grill regulator problems
I hope this is all clear now all you need to know about gas grill regulator problems, but if something is still unclear then don’t hesitate to leave a comment below and I’ll try my best to answer as soon as possible.
Also keep in mind that depending on your grill model & brand these tips might work differently so always double check before doing anything.
Additionally, this article is not intended as a step by step guide but rather as a general overview because I don’t have access to all grills which makes it impossible for me to test each and every one of them.
Thanks for reading!
Read more: How Long To Smoke A 20lb Turkey?